|
Post by ceratov2m on Sept 17, 2008 20:55:16 GMT 8
Hi all! Would like to know wat is V2's clutch plate size?Iszit the same as V1 at 8.5 inch? Many thanks!
|
|
siqma
Gear THREE
juz sHuT-uP & DrIvE,DrIVe,dRiVe
Posts: 375
|
Post by siqma on Sept 18, 2008 1:17:57 GMT 8
|
|
|
Post by ceratov2m on Sept 18, 2008 3:28:42 GMT 8
No lar...juz asking for sport clutch nia...racing too stiff lar... Any recommendations? Wat model of Exedy clutch does the Variant R use?
|
|
|
Post by BluePicanto on Sept 18, 2008 16:51:31 GMT 8
Call creative sports lo... They'r the 1 tuned up the Variant R.
|
|
|
Post by ceratov2m on Sept 18, 2008 23:46:44 GMT 8
Call creative sports lo... They'r the 1 tuned up the Variant R. Ok! But do u happen to have their contacts and address? Thx a lot in advance for yr assistance!
|
|
siqma
Gear THREE
juz sHuT-uP & DrIvE,DrIVe,dRiVe
Posts: 375
|
Post by siqma on Sept 19, 2008 0:21:19 GMT 8
check wit pysfool la i tink he using Exedy clutch
|
|
|
Post by subzero on Sept 19, 2008 8:26:26 GMT 8
I dun think its the same for V2..
|
|
|
Post by BluePicanto on Sept 19, 2008 10:19:53 GMT 8
Think should b diff coz V2 reverse gear is beside gear 1 instead of below gear 5 fr V1.
|
|
|
Post by 250whp on Sept 19, 2008 21:54:43 GMT 8
I think v1 and v2 clutches are the same. The diff reverse position is not an issue coz the clutch is located before your gear box.And some tips if u wanna get the clutch is tat do not only see the OD size of the clutches but the center hole on the clutch (for the shaft ) Should also be the same if not cannot install.The best way for u since you are not so sure is that you should go to workshop that sell and install. Maybe abit expensive but will waste money and time if u get the wrong part. Cheers....
|
|
|
Post by psyfool7 on Sept 20, 2008 0:00:40 GMT 8
check wit pysfool la i tink he using Exedy clutch He checked wif me oready...But I too not sure same or not.. ....Got possibilty the same...
|
|
siqma
Gear THREE
juz sHuT-uP & DrIvE,DrIVe,dRiVe
Posts: 375
|
Post by siqma on Sept 20, 2008 1:43:40 GMT 8
Think should b diff coz V2 reverse gear is beside gear 1 instead of below gear 5 fr V1. i tink gear position got no issue la
|
|
|
Post by ceratov2m on Sept 21, 2008 2:34:31 GMT 8
check wit pysfool la i tink he using Exedy clutch roger n thks!will chk wif him!
|
|
|
Post by psyfool7 on Sept 21, 2008 11:02:55 GMT 8
check wit pysfool la i tink he using Exedy clutch roger n thks!will chk wif him! If the same, then u can get the same as wat I'm using....Exedy Clutch plate MD05S and Clutch cover/ pressure plate MC05T...
|
|
siqma
Gear THREE
juz sHuT-uP & DrIvE,DrIVe,dRiVe
Posts: 375
|
Post by siqma on Sept 22, 2008 1:46:16 GMT 8
IMO, using this 'mod', later press the clutch a bit hard
|
|
|
Post by psyfool7 on Sept 22, 2008 2:00:51 GMT 8
Yup...quite hard...But I'm getting used to it..Jam at the causeway will really train up ur left leg...tink my left leg getting bigger liao...
|
|
|
Post by subzero on Sept 22, 2008 12:42:14 GMT 8
After u got used to it, can switch to multiples plates already... Heheheh..
|
|
|
Post by psyfool7 on Sept 22, 2008 19:45:38 GMT 8
After u got used to it, can switch to multiples plates already... Heheheh.. U mean the Ice Cream type?...Make a lot of noise one?...Forget it lah...no point..car not powerful enuff to hav such hardcore clutches...
|
|
|
Post by d1nzfe on Sept 22, 2008 22:43:53 GMT 8
oh btw is this wat the variant r is using? i like the feel of the R one
|
|
siqma
Gear THREE
juz sHuT-uP & DrIvE,DrIVe,dRiVe
Posts: 375
|
Post by siqma on Sept 23, 2008 0:46:03 GMT 8
|
|
|
Post by ceratov2m on Oct 13, 2008 2:38:36 GMT 8
oh btw is this wat the variant r is using? i like the feel of the R one Wah!U oso inside Kia forum ar?Seems like u r everywhere!
|
|
|
Post by ceratov2m on Oct 21, 2008 4:08:05 GMT 8
roger n thks!will chk wif him! If the same, then u can get the same as wat I'm using....Exedy Clutch plate MD05S and Clutch cover/ pressure plate MC05T... Did u change the clutch fluid and manual transmission fluid as well when u replaced the whole set-up? Other den orig clutch bearings I hv 2 buy, any other things which I hv to gt it from stockist? E.g-fluids, etc... Thks!
|
|
|
Post by psyfool7 on Oct 21, 2008 20:12:19 GMT 8
If the same, then u can get the same as wat I'm using....Exedy Clutch plate MD05S and Clutch cover/ pressure plate MC05T... Did u change the clutch fluid and manual transmission fluid as well when u replaced the whole set-up? Other den orig clutch bearings I hv 2 buy, any other things which I hv to gt it from stockist? E.g-fluids, etc... Thks! I juz leave it to the workshop lor..bearings were changed..gear oil oso as need to drain..he didn't charge me for anything else..
|
|
|
Post by ceratov2m on Oct 22, 2008 2:17:02 GMT 8
Alrite and thks, Bro Psyfool...U've been a great help!
|
|
|
Post by ceratov2m on Nov 1, 2008 5:07:29 GMT 8
Latest update!
Confirm V1's clutch plate's size able to fit V2 even though different engine and gear configuration!
However, the clutch release bearing is different, I'll be goin back to Min Gheee to seek for a replacement or does anyone need a clutch release bearing for V1 when changing clutch plate?I'm selling cheaper den wat u cn get from Min Ghee!
|
|
|
Post by psyfool7 on Nov 1, 2008 11:48:36 GMT 8
Latest update! Confirm V1's clutch plate's size able to fit V2 even though different engine and gear configuration! However, the clutch release bearing is different, I'll be goin back to Min Gheee to seek for a replacement or does anyone need a clutch release bearing for V1 when changing clutch plate?I'm selling cheaper den wat u cn get from Min Ghee! I tot u fixed oready?..So muz take out again to change the bearing?..
|
|