|
Post by kennyboy on Aug 26, 2012 12:53:42 GMT 8
Where are you doing your SSBH? bro i did mine at Hock Lian Motor Service...nice boss!!
|
|
|
Post by kennyboy on Aug 26, 2012 12:44:45 GMT 8
Well, i back to share the results after installing the ssbh. Its firmer and with no sinking feeling, brake response is sharper and faster...step a bit can start to feel the car slow down.
I using magnum ssbh - 6 pieces
|
|
|
Post by kennyboy on Aug 24, 2012 12:03:59 GMT 8
Muahahax...sounds gd too!!
|
|
|
Post by kennyboy on Aug 24, 2012 10:41:08 GMT 8
Oh well...seems like all this is just wishful thinking...only in SG...if in US...confirm gut the car inside out and drop a 2L.....haiz....
|
|
|
Post by kennyboy on Aug 24, 2012 10:34:11 GMT 8
Oh..i wanted to make a hole for the air scoop better for open pod...anyway planning to look for lobang to do aluminium or carbon panels..for the bonnet and fenders...change the seats to those light ones...overall just to lighten the car..hopefully can find...lol
|
|
|
Post by kennyboy on Aug 23, 2012 22:04:21 GMT 8
I wanna keep the stock look mah..dun wanna customise so much since car already heavy, plus bodykit even heavier...the most change bonnet.
Wanna ask if bonnet cut hole illegal?
|
|
|
Post by kennyboy on Aug 23, 2012 21:45:41 GMT 8
Bro, im not sure if u have solved the problem but i use to have this issues before after replacing the battery from the car dealer. During changing or cleaning of the internals of the remotes, they may have unintentionally adjust the freq module for your remote...u can try to reset by opening up ur other remote and copy the direction of the tuner, use that as a starting point and slowly adjust + / - till u can command with ur remote. After you have set the freq, use a drop of super glue to seal the little tuner so u dun have this issues again.
|
|
|
Post by kennyboy on Aug 23, 2012 15:30:29 GMT 8
|
|
|
Post by kennyboy on Aug 23, 2012 12:58:25 GMT 8
Hey guys,
i wanna check if its possible to install stock V2 bumpers and bonnet on a V1?
Thanks!
|
|
|
Post by kennyboy on Aug 23, 2012 12:34:13 GMT 8
Brake feel is better rite?
|
|
|
Post by kennyboy on Aug 23, 2012 11:41:36 GMT 8
Dunnoe considered new?? LOL got my ride for 2yrs liao...now den join forum!! Black/V1/HB/Manual
|
|
|
Post by kennyboy on Aug 22, 2012 16:51:08 GMT 8
btw im using Rev-X w30
|
|
|
Post by kennyboy on Aug 22, 2012 16:49:35 GMT 8
Mine FC 12.7km/L..setup: yoko s drive 205/50/16 F300psi R250psi K&N drop-in air filter
However, i realised its mainly driving habits....on expressway try hold ur rpm steady and up gear early...if i drive badly FC is only 10.4km/L
u may wanna try to adjust ur driving habits before doing any replacements
|
|
|
Post by kennyboy on Aug 22, 2012 14:41:05 GMT 8
I'm doing this coming friday will try take photo before they install so can show u guys!!
|
|
|
Post by kennyboy on Aug 22, 2012 11:06:33 GMT 8
Well, its very spongy and the worse thing is at stationary, when u depress the brake, its okie but after holding down the brakes for a while, the pedal will sink further..this is not due to moisture in the fluid as i had mine change and rebled. As what bro unocvin had said...its due to expansion of the rubber hose. I have tried those whom have change and it provided a very positive feedback (not spongy at all) as well as stopping power (faster response). For those whom are planning to change, u shld do as its a worthwhile upgrade but please find a reputable workshop as its the only mechanism that stops ur car.
|
|
|
Post by kennyboy on Aug 21, 2012 17:58:18 GMT 8
Is there any risk involved with customised brake lines?
|
|
|
Post by kennyboy on Aug 21, 2012 13:09:27 GMT 8
Hi guys,
Im new to this forum and hoping to get some help.
I have been driving my V1 HB for almost 2yrs liao..wanna do some upgrade to spicy things up a little.
I read from previous post about a group buy for IMP Steel Hose in JB. Any bro care to give me some feedbacks?
Able to get in SG? What is the pricing?
Thanks in advance!
|
|